Parent-child track relationships can be defined in the track’s routing window, opened by clicking on its Route button in the track panel.
可以在轨道的路由窗口中定义父级子级轨道关系,该窗口通过单击轨道面板中的“路由”按钮打开。
By default, REAPER assumes that you require two channels (1-2) for new tracks, and 2 channels (1-2) for the master. These channels (in this example 1 and 2, because that is all there are) are used to send output from the track to its parent (which in this example is the master, as shown above right). The first of the paired dropdowns determines and indicates the channels used to send output from the track to the master, the second indicates the channels on the master to which they are to be sent.
默认情况下,REAPER假设您需要两个通道(1-2)用于新轨道,2个通道(1至2)用于主控,并且您需要将全部通道(在本例中为1和2,因为只有这两个通道)从轨道发送到主控(如右上方所示)。成对下拉列表中的第一个确定要从轨道发送到主控的通道,第二个确定要将它们发送到哪个主控通道。
Note that the parent will not always be the master. An example is when the track is contained within a folder. In this case, instead of Master send channels from/to the dialog will display Parent send channels from/to, and the output will be directed to the folder track, not directly to the master.
请注意,父级并不总是主控。例如,当轨道包含在文件夹中时。在这种情况下,对话框将显示“父级发送通道从/到”,而不是“主控发送通道从/到”,输出将指向文件夹轨道,而不是直接指向主控。
There might be occasions when you will need more than two channels - for example when sidechaining, using parallel FX processing, or if you are producing output in surround sound format. In any such case, you will need to specify the number of track channels required and their relationship to their parent.
在某些情况下,您可能需要两个以上的通道,例如,使用并行FX处理进行侧链时,或者您正在以环绕声格式输出。在任何这种情况下,您都需要指定所需的轨道通道的数量及其与父级通道的关系。
Example 1:
示例1
In this case the track has four channels (perhaps reserving channels 3-4 for sidechaining detector input), but only channels 1-2 are to go to the parent (master). We select 1-2 from the first dropdown, and from the second dropdown we select 1-2 as our destination channels in the master.
在这种情况下,轨道有四个通道(可能为侧链检测器输入保留通道3-4),但只有通道1-2要输送到父级(主控)。我们从第一个下拉列表中选择1-2,然后从第二个下拉列表选择1-2作为主控中的目标通道。
Example 2
示例2
This next example would be suitable for surround mixing in 5.1 format. The master has been defined as having six channels, as have the tracks. Hence, from the first dropdown we can select either All or 1-6 channels: 1-6 is automatically selected for the second dropdown, because once we have specified that we wish to send all 6 channels that becomes the only possible option.
下一个示例适用于5.1格式的环绕混缩。主控被定义为具有六个通道,轨道也是如此。因此,从第一个下拉列表中,我们可以选择全部或1-6个通道:第二个下拉列表自动选择1-6个通道,因为一旦我们指定要发送全部6个通道,这将成为唯一可能的选项。
Example 3
示例3
This final example is for a child track within a folder. The track itself has only 2 channels, but the folder has 4 (perhaps for manipulating FX within the folder’s FX chain). Here we select All or 1-2 from the first dropdown: because this track has only two channels, in this case either of these will produce the same result. However, because the parent contains four channel, we must also specify the destination channels on the folder. If you do not make a selection, it will default to 1-2.
最后一个示例是文件夹中的子级轨道。轨道本身只有2个通道,但文件夹有4个通道(可能用于在文件夹的FX链中操纵FX)。在这里,我们从第一个下拉列表中选择全部或1-2:因为这个轨道只有两个通道,在这种情况下,这两个通道中的任何一个都会产生相同的结果。但是,因为父级包含四个通道,所以我们还必须在文件夹中指定目标通道。如果不进行选择,则默认为1-2。
Tip: You can change the number of default channels for new tracks to any even number up to 64 on the Advanced page of Project Settings. Here you can also change the default number of parent send channels.
提示: 在“工程设置”的“高级”页面上,您可以将新轨道的默认通道数更改为最多64个的任意偶数。在这里,您还可以更改父级发送通道的默认数量。 作者: 琴韵晓波 时间: 2022-12-25 18:16 点此转到本章目录点此转到总目录——【本文译者：王晓波，出处：视障者音乐制作交流基地】点此转到REAPER+SWS+OSARA中文语言包下载页面