7.4 自动修剪/分割对象——REAPER用户手册中文版

琴韵晓波

楼主 琴韵晓波说：
7.4 Auto Trim/Split Items
7.4 自动修剪/分割对象

REAPER's action list contains literally hundreds of commands and actions, many of which are not shown on any menus. Actions are covered in more depth in Chapter 15.
REAPER的操作列表包含数以百计的命令和操作,其中许多没有显示在任何菜单上。操作在第15章中有更深入的介绍。
Two actions worth looking at here are Item: Auto trim/split items (remove silence) and Transient detection sensitivity/threshold (adjust). These two can work together.
这里有两个值得关注的操作: “对象: 自动修剪/分割对象(移除静音)...”,和“瞬态检测灵敏度/阈值: 调整...”。这两个操作可以协同工作。
Actions are run by first choosing the Actions, Show actions list command from the main menu, then selecting the required action and clicking Run. Note both that the Actions menu includes an option to Show recent actions on menu, and that within the Actions list you can use the Filter box to help find an action.
首先从主菜单中选择“操作”、“显示操作列表”命令,然后选择所需的操作并单击运行,即可运行操作。请注意,“操作”菜单包含一个在菜单上显示近期操作的选项,并且在“操作”列表中,您可以使用“过滤器”框来帮助查找操作。
Auto trim/split items is similar to using dynamic splitting to remove silence, except that it supplies you with some additional options. Selecting an item and running this action opens the dialog box shown here.
自动修剪/分割对象,类似于使用动态分割来移除静默区,不同之处在于,它为您提供了一些附加选项。选择一个对象并运行此操作,将打开此处显示的对话框。
Threshold and Hysteresis control the noise gate to determine the level below which passages are removed, and the degree of sensitivity applied - the same as with dynamic splitting.
“阈值”和“滞后”控制噪声门,以确定段落被移除的电平,以及应用的灵敏度——与动态分割相同。
Similarly, the controls Ignore silence..., Make non-silent clips no shorter than..., Pad controls and Auto adjust snap... all work in the same way as their equivalent dynamic splitting options.
类似地,控制“忽略静音”、“使非静默剪辑不短于”、“铺底控制”和“自动调整吸附”所有选项的工作方式与其等效的动态分割选项相同。
The Mode drop-down has four options - Split and remove silent areas, Split and keep silent areas, Split only before non-silence and Split only before silence.
“模式”下拉列表有四个选项——“分割并移除静默区域”、“分割并保留静默区域”、“仅在非静音之前分割”和“仅在静音之前分割”。
If working with a set of grouped items, you have the option to Split grouped items at times of selected item splits.
如果使用一组编组对象,则可以选择“分割选中的对象时,分割编组的对象”。
You can also set the gate to be applied post-FX by enabling the option Run signal through track FX for detection. This, for example, could be used to avoid chopping off any delay or reverb tails caused by track FX.
您还可以通过启用选项“通过轨道FX运行信号进行检测”来设置要在FX后应用的门限。例如,这可以用来避免截断由轨道FX引起的任何延迟或混响的尾音。
If you also run the action Transient detection sensitivity/threshold a pair of faint horizontal lines will be displayed to give you visual feedback on your gate settings.
如果你也运行操作“瞬态检测灵敏度/阈值”,将显示一对模糊的水平线,为你的门限设置提供视觉反馈。
Another option is Use zero crossings when splitting. This can prevent audio clicks on playback.
另一个选项是,在分割时使用零交叉点。这可以防止播放时出现音频卡嗒声。

琴韵晓波

沙发 琴韵晓波说：
点此转到本章目录    点此转到总目录——【本文译者：王晓波，出处：视障者音乐制作交流基地】    点此转到REAPER+SWS+OSARA中文语言包下载页面