23.2 设置ReaRoute的应用程序——REAPER用户手册中文版

琴韵晓波

楼主 琴韵晓波说：
23.2 Setting Up Applications for ReaRoute
23.2 设置ReaRoute的应用程序

Before you can use any audio application with REAPER via ReaRoute, you need to ensure that the audio settings for that application are set up correctly. There are usually one or two basic steps involved. The first is to enable ReaRoute ASIO as the preferred driver, the second is to enable the various input and output channels required to transmit audio between the application and REAPER. With some applications, this second step is not required. The method will vary with the application, but always involve specifying your preferences on the Audio Settings dialog box (or similar). The table below gives some examples. They are accurate at the time this is being written, but be aware that all software programs are likely to change over time. Note that before setting up or using any application for use with ReaRoute, you should 1) make sure that the ReaRoute ASIO Driver has been installed (see previous page), and 2) make sure that REAPER is open and minimised.
在通过ReaRoute将任何音频应用程序与REAPER一起使用之前,您需要确保该应用程序的音频设置设置正确。通常涉及一到两个基本步骤。第一个是启用ReaRoute ASIO作为首选驱动程序,第二个是启用在应用程序和REAPER之间传输音频所需的各种输入和输出通道。对于某些应用程序,不需要第二步。该方法因应用程序而异,但始终涉及在“音频设置”对话框(或类似对话框)中指定您的首选项。下表给出了一些例子。它们在编写时是准确的,但要注意所有软件程序都可能随着时间的推移而变化。请注意,在设置或使用任何用于ReaRoute的应用程序之前,您应该1)确保已安装ReaRoute ASIO驱动程序(请参阅上一页),2)确保REAPER已打开并最小化。
Application Instructions
应用    说明
Ableton Live
1. Options, Preferences then click on the Audio tab.
1.“Options(选项)”、“Preferences(首选项)”,然后单击“Audio(音频)”选项卡。
2. Set Driver Type to ASIO.
2.将“Driver Type(驱动程序类型)”设置为ASIO。
3. Set Audio Device to ReaRoute ASIO.
3.将“Audio Device(音频设备)”设置为“ReaRoute ASIO(重新路由ASIO)”。
4. Click on Input Config then on each input channel to be enabled, then OK.
4.单击“Input Config(输入配置)”,然后单击要启用的每个输入通道,然后单击“OK(确定)”。
5. Click on Output Config then on each output channel to be enabled, then OK.
5.单击“Output Config(输出配置)”,然后单击要启用的每个输出通道,然后单击“OK(确定)”。
6. Close Preferences window.
6.关闭“首选项”窗口。
FL Studio
Options, Audio Settings, then select ReaRoute ASIO for Output. Close Audio Settings window.
“Options(选项)”、“Audio Settings(音频设置)”,然后选择“ReaRoute ASIO”进行输出。关闭音频设置窗口。
Note for macOS users:
macOS用户注意:
Although the macOS does not support ReaRoute, there is third party software available, such as Soundflower and Loopback (by Rogue Amoeba), which can perform similar functions.
虽然MacOS不支持ReaRoute,但也有第三方软件可用,如Soundflower和Loopback(由Rogue Amoeba开发),它们可以执行类似的功能。

琴韵晓波

沙发 琴韵晓波说：
点此转到本章目录    点此转到总目录——【本文译者：王晓波，出处：视障者音乐制作交流基地】    点此转到REAPER+SWS+OSARA中文语言包下载页面