18.28 轨道发送自动化——REAPER用户手册中文版

琴韵晓波

楼主 琴韵晓波说：
18.28 Automation with Track Sends
18.28 轨道发送自动化

Automation can be applied to other controls beside Volume and Pan, such as Sends and FX parameters. In this example, we will create a Send, then use an envelope to control it.
自动化可以应用于除音量和声像之外的其他控件,如发送和FX参数。在本例中,我们将创建一个发送,然后使用包络来控制它。
Example
示例
1. First, we are going to create an FX Bus Track, then we will use an envelope to vary the level sent to that FX Bus Track from each of the guitar tracks.
1.首先,我们将创建一个FX总线轨道,然后我们将使用一个包络来改变从每条吉他轨道发送到该FX总线轨道的电平。
2. Create a new track and name it FX Bus. Display the FX Chain for this track, and add the FX JS Chorus. Close the FX window.
2.创建一条新轨道,并将其命名为FX Bus。显示此轨道的FX链,并添加FX JS Chorus。关闭FX窗口。
3. Select the track Gtr Body and drag and drop from its ROUTE button to the FX Bus to create a send. Set send volume to -10 and pan to 65L as shown (above).
3.选择Gtr Body轨道,并从其路由按钮拖放到FX Bus,以创建发送。如上图所示,将发送的音量设置为-10,将声像设置为65左。
4. Select the track Gtr Neck and display the routing window for this track. Create a send to the FX Bus as a send and set send volume to - 10dB and pan to 65% Right.
4.选择Gtr Neck轨道,并显示此轨道的路由窗口。创建一个到FX Bus的发送作为发送,并将发送音量设置为-10dB,将声像设置为65%右。
5. Now display the Envelopes window for the Gtr Body track. Set mode to Trim/Read. Notice that envelopes are available for your sends. Make sure that the FX Bus Send Volume is selected, visible and armed.
5.现在显示Gtr Body轨道的包络窗口。将模式设置为“修剪/读取”。请注意,包络可供您发送。确保FX Bus的发送音量处于选中、可见和预备状态。
6. Close this window. An envelope lane for this send will now be visible just below track.
6.关闭此窗口。此发送的包络子轨,现在将在轨道下方可见。
7. Hover the mouse over any part of the envelope, click and drag down until the envelope is set to about -12dB.
7.将鼠标悬停在包络的任何部分上,单击并向下拖动,直到包络设置为大约-12dB。
8. We are now going to increase the chorus effect, starting just before the second verse.
8.我们现在要增加合唱效果,从第二段之前开始。
9. Add a point at about the 60 second point (Shift Click). Add another point at about 2:30.
9.在大约60秒处添加一个点(Shift+单击)。在2:30左右的地方再添加一个点。
10. Hover the mouse over the envelope just after this second point. Click and drag up until the envelope is set to about -7dB. Release the mouse. This is shown below.
10.将鼠标悬停在第二个点之后的包络上。单击并向上拖动,直到包络设置为大约-7db。松开鼠标。如下所示。
11. Set the track automation mode to Read. Play the song. If the chorus effect is too much, hover the mouse over the envelope, round about 1 minute 30 secs, then click and hold the left mouse button while you drag the it back down a little.
11.将此轨道的自动化模式设置为“读取”。播放这首歌。如果您认为合唱效果太大,请将鼠标悬停在包络上大约1分30秒处,然后单击并按住鼠标左键,同时将包络向下拖动一点。
12. Now repeat steps 5. to 10. for the track Gtr Neck. Don’t forget to save the file.
12.现在对Gtr Neck轨道重复步骤5至10。别忘了保存文件。

琴韵晓波

沙发 琴韵晓波说：
点此转到本章目录    点此转到总目录——【本文译者：王晓波，出处：视障者音乐制作交流基地】    点此转到REAPER+SWS+OSARA中文语言包下载页面